Should I Use 1/4 Or 1/2 Cement Board
You should be using a minimum of 1/2″ thick cement board for shower walls. 1/4 usg durock® cement board is an ideal substrate for floor and countertop ceramic tile installations.
The 1/4 thickness helps eliminate transition trim when abutting carpet or wood flooring and minimize level variations with other finish materials.
Should i use 1/4 or 1/2 cement board. Never use a 1/4″ thick cement board for shower walls as this will deflect and flex if it is pushed or bumped accidentally. 1/4 inch, ½ inch, and 5/8 inch thick cement board panels are all appropriate for countertop installations. 1/4 durock cement board should not be used for wall or ceiling applications.
The extra thickness is needed to span the studs and provide a solid base for the tile. You should also be undercutting you jambs and casings to accept the tuck of the cement board and the tile and the two layers of. What subfloor should hardiebacker board be installed over?
#7 · feb 24, 2008 (edited) use 1/2 cement board in your shower wall area. 1/4 hardibacker alone is an unsuitable substrate for shower wall tile. It should be almost unnoticeable if done right.
Make that up, by having the tile sit over the cement board just slightly, (where it meets the 3/8 s/r). My thought process at the time was i used a 1/2” trowel for 12”x24” tile so it made sense i’d need a larger trowel for cement board. That way, the difference will only be 1/8.
I laid my cement board on top of plywood using a 1/2” trowel instead of a 1/4” trowel. Don't use regular drywall or wood screws, which corrode in cement board. The minimum subfloor specified is 5/8 exterior grade plywood or 23/32'' exterior grade osb subflooring.
It does not belong as a floor or a roof; This will be rigid and strong enough to resist any deflection or flexing from any impact on the wall. Either can be used on floors but only 1/2 can be used on walls.
Durock 1/4 is made for floors. That said, for safety’s sake, especially with a wood burning fireplace, 1/2” cement board is ideal for under your fireplace surround tile. 1/2 plywood is for temporary applications, exterior sheathing and used as gigantic shims.
Technical data property astm test reference 1/4 value flexural strength c947 >1000 psi indention strength d2394 >1250 psi weight c473 <1.9 psf A cement board with a minimum thickness of ¼ inch is required, but thicker panels may also be used. For wall or ceiling applications, use 1/2 or 5/8 usg durock® cement board.
1/4 usg durock® cement board should not be used for wall or ceiling applications. Foam shower tile backer boards are generally about 4x the cost of cement board. It’s recommended to use ½ inch or 5/8 inch thick cement board for walls.
Think about it, one wayward elbow, knee, or hip bump and you may get flexion which would cause the grout (or tile) to crack. For flooring or wall installation, some builders choose to apply a thin layer of thinset mortar under the cement. If it were attached to properly waterproofed drywall, plywood, or plaster it would be fine.
The minimum recommended thickness for the shower wall is 1/2″ because like some of the other boards, they become far too flexible at thicknesses below 1/2″. For wall or ceiling applications, use 1/2 or 5/8 durock cement board.if you have 3/8 sheetrock, use 1/2 cement board and feather out the joint to approx 10 to 12. Apply a layer of mortar.
Also, can you use 1/4 cement board on floors? Spread a thin layer of mortar over the concrete, following instructions from your manufacturer.